R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
SG / TE / XT Series
WARNING:
Read and follow all Safety Rules and Operating Instructions be-
fore using this product. Read instructions carefully before assem-
bling. Failure to do so can result in serious injury.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
Copyright E2003 Electrolux Home Products, Inc.
530084129
2/11/03
electrical rating not less than the rating
of unit. Cord must be marked with suf-
fix “W--A” (in Canada “W”). Make sure
your extension cord is in good condi-
tion. Inspect extension cord before use
and replace if damaged. Do not use a
damaged cord. Cord insulation must
be intact with no cracks or deteriora-
tion. Plug connectors must be undam-
aged. An undersized extension cord
will cause a drop in line voltage result-
ing in loss of power and overheating. If
in doubt, use the next heavier gauge.
The lower the gauge number, the
heavier the cord (see SELECT AN EX-
TENSION CORD). Do not use multiple
cords.
S Do not abuse cord. Never carry the unit
by the extension cord or yank exten-
sion cord to disconnect unit.
S Use cord retainer to prevent discon-
nection of extension cord from unit.
See ATTACH THE EXTENSION CORDTO
YOUR TRIMMER in the OPERATION sec-
tion.
S Do not use the unit if the switch does
not turn the unit on and off properly. Re-
pairs to the switch must be made by
your authorized service dealer.
S Keep the extension cord clear of oper-
ator and obstacles at all times. Do not
expose cords to heat, oil, water, or
sharp edges.
S To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on cir-
cuit or outlet to be used. Receptacles
are available having built-in GFCI
protection and may be used for this
measure of safety.
S Use only recommended Weed Eaterr
replacement parts and accessories.
CUTTING SAFETY
S Inspect area to be cut. Remove objects
(rocks, broken glass, nails, wire, string,
etc.) which can be thrown or become
entangled in cutting head.
S Do not overreach or stand on unstable
support. Keep firm footing and balance.
S Keep the cutting head below waist lev-
el. Do not raise handles above your
waist. Cutting head can come danger-
ously close to your body.
S Keep away from cutting head and spin-
ning line.
S Use unit properly. Use only for trim-
ming, edging, and mowing. Do not
force unit; it will do the job better and
with less risk of injury at the rate for
which it was designed.
S Use only in daylight or in good artificial
light.
MAINTENANCE SAFETY
WARNING: Disconnect unit from
the power supply before performing
maintenance, or when changing trimmer
line.
S Maintain unit according to recom-
mended procedures. Keep cutting line
at proper length. Follow instructions for
changing trimmer line.
S Have all service and maintenance not
explained in this manual performed by
an authorized service dealer to avoid
creating a hazard.
S Never douse or squirt the unit with water
or any other liquid. Clean unit and labels
with a damp sponge. Keep handles dry,
clean, and free from oil and grease.
S Keep the air vents clean and free from
debris to avoid overheating the motor.
Clean after each use.
TRANSPORTING AND STORAGE
S Stop the unit and disconnect the power
source when not in use.
S Carry the unit with motor stopped.
S Store the unit so that the line limiter
blade (on underside of shield) cannot
cause injury.
S Store unit indoors in a high, dry place
out of the reach of children. Store unit
unplugged.
UNIT SAFETY
S Inspect unit before use. Replace dam-
aged parts. Make sure all handles,
guards, and fasteners are in place and
securely fastened. Parts that are dam-
aged must be repaired or replaced by
an authorized service dealer. This in-
cludes head parts that are cracked, or
chipped, guards, and any other part
that is damaged.
S Do not repair unit yourself.
S Use only 0.065” (1.65 mm) diameter
recommended trimmer line (see ACCE-
SORIES). Never use wire, rope, string,
etc.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help pro-
tect against electric shock. Double in-
sulation construction consists of two
separate “layers” of electrical insulation
instead of grounding.
S Use specified trimmer spool. Make
sure spool is properly installed and all
parts are securely fastened.
3
Tools built with this insulation system are
not intended to be grounded. No ground-
ing means is provided on this unit, nor
should a means of grounding be added
to this unit. As a result, the extension
cord used with your unit can be plugged
into any standard 120 volt electrical out-
let.
ALIGN INSTALLATION ARROWS
Safety precautions must be observed
when operating any electrical tool. The
double insulation system only provides
added protection against injury resulting
from an internal electrical insulation failure.
Twist shield in
direction of
WARNING: All electrical repairs to
this unit, including housing, switch, mo-
tor, etc., must be diagnosed and repaired
by qualified service personnel. Replace-
ment parts for a double insulated ap-
pliance must be recommended by the
manufacturer. A double insulated ap-
pliance is marked with the words “double
insulation” or “double insulated.” the
symbol (square within a square) may
also be marked on the appliance. Failure
to have the unit repaired by qualified ser-
vice personnel can cause the double in-
sulation construction to become ineffec-
tive and result in serious injury.
arrow to assemble
CAUTION: Sharp line limiter blade
Place handle in
comfortable
position and
tighten securely.
NOTE: SG & XT units are equipped with
an extendable tube. Extend the tube until
it snaps into place. Without the tube fully
extended the Twist ’N Edge feature on
the XT series will not operate.
SAVE THESE INSTRUCTIONS
Extendable tube
(Some models)
ASSEMBLY
WARNING: If you receive your unit
assembled, check each step to insure
your unit is properly assembled. Follow
all safety information in the manual and
on unit.
CAUTION: The tube must be fully ex-
tended for the unit to operate correctly.
USING YOUR UNIT
Use only a voltage supply as specified
on your unit.
WARNING: The shield must be
properly installed. The shield provides
partial protection from the risk of thrown
objects to the operator and others. Your
unit is equipped with a line limiter blade,
which cuts excess line to the proper
length while running. The line limiter
blade (on underside of shield) is sharp
and can cut you.
SELECT AN EXTENSION CORD
Extension Cord Gauge Chart
Length of Cord
Gauge
18 Gauge
16 Gauge
16 Gauge
25 Ft. (7.5 m)
50 Ft. (15 m)
100 Ft. (30 m)
NOTE: If shield is not properly installed,
damage to unit (including motor failure)
will result.
Extension cords are available for this
unit.
ATTACH THE EXTENSION
CORD TO YOUR TRIMMER
Loop your extension cord through the
handle and around the hook. Insure the
plug and cord are firmly and fully en-
gaged.
4
TAP
Cutting
Head
Metal Blade
TWIST ‘N EDGEr FEATURE
CORRECT OPERATING POSITION
XT & TE series units are equipped with a
button on the side of the unit. If your unit
includes this feature you can press this
button and twist the lower portion 180_
counterclockwise into an edging posi-
tion.
Twist ‘N Edge Button
(XT & TE)
MAINTENANCE
Edging
Trimming
WARNING: Disconnect power
WARNING: Always wear eye pro-
tection. Never lean over the trimmer
head. Rocks or debris can ricochet or be
thrown into eyes and face and cause
blindness or other serious injury.
source before performing maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to opera-
tor abuse or negligence. To receive full
value from the warranty, the operator
must maintain unit as instructed in this
manual. Various adjustments will need to
be made periodically to properly main-
tain your unit.
When operating unit, stand as shown and
check for the following:
S Wear eye protection and heavy clothing.
S Hold trigger handle with right hand and
assist handle with left hand.
S Keep unit below waist level.
BEFORE EACH USE
S Cut from your right to your left to ensure
debris is thrown away from you. With-
out bending over, keep line near and
parallel to the ground (perpendicular
when edging) and not crowded into
material being cut.
CHECK FOR LOOSE FASTENERS
AND PARTS
S Housing Screws
S Assist Handle
S Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
ADJUSTING UPPER HANDLE
(XT Series only)
S Press button located on the underside
of the upper handle and extend handle
to a comfortable position.
Contact an authorized service dealer for
replacement of damaged or worn parts.
S Trigger Switch -- Ensure switch func-
tions properly by pressing and releas-
ing the trigger switch. Make sure motor
stops.
S Debris Shield -- Discontinue use of unit
if debris shield is damaged.
Button
AFTER EACH USE
INSPECT AND CLEAN UNIT AND LA-
BELS
ADVANCING THE CUTTING LINE
To advance the line, tap the bottom of the
cutting head on the groundwhile thetrim-
mer is running at full speed. The metal
blade attached to the shield will cut the
line to the proper length.
S After each use, inspect complete unit
for loose or damaged parts. Clean the
unit using a damp cloth with a mild de-
tergent.
S Wipe off unit with a clean dry cloth.
5
S Align the notch with the line exit hole.
S Push the spool into the hub until it
snaps into place, while keeping light
tension on the end of the line.
S Pull on the line extending outside of the
hub to release it from the notch; other-
wise, the unit will not function properly.
SERVICE
REPLACING THE LINE
S Disconnect unit from the powersource.
S Remove the spool by firmly pulling on
the tap button.
S Clean entire surface of hub and spool.
S Replace with a pre-wound spool, or cut a
length of 30 feet of 0.065 diameter Weed
Eaterr brand line. Use of heavier line
could overload and damage the unit.
Never use wire, rope, string, etc., which
can break off and become a dangerous
missile.
STORAGE
WARNING: Perform the following
steps after each use.
S Stop the unit and disconnect the power
source when not in use.
S Carry the unit with motor stopped.
S Store the unit so the line limiter blade
cannot cause injury.
S Store unit and extension cord indoors
in a high, dry place out of the reach of
children. Store unit unplugged.
S Insert one end of the line about 1/2 inch
(1 cm) into the small slot inside the spool.
Small
Hole
Spool
S Store unit with all guards in place. Posi-
tion unit so that any sharp object can-
not accidentally cause injury.
S Wind the line evenly and tightly onto
the spool. Wind in the direction of the
arrow found on the spool.
S Push the line into the notch, leaving 3
to 5 inches (7 -- 12 cm) unwound.
S Insert the line into the exit hole in the
hub as shown in the illustration.
Line in
NEED ASSISTANCE?
For assistance, or a replacement part
call: 1-800-554-6723.
Notch
Safety Glasses
952701645
Spool with 30’ line 952701663
50’ coil of bulk line. 952701550
100’ coil of line.
200’ coil of line.
952701533
952701594
Hub
Line exit hole
6
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before
performing all of the recommended remedies below except remedies that re-
quire operation of the unit.
TROUBLE
CAUSE
REMEDY
Semi-automatic
head stops
1. Allow tip of line to do the cutting.
1. Crowding trimmer line
against material being
cut.
under a load or
does not turn
when switch is
pressed.
2. Contact your authorized service dealer.
3. Check Breaker Box.
4. Remove debris.
2. Electrical failure.
3. Thrown circuit breaker.
4. Debris stopping head.
Line does not
advance or
breaks while
cutting.
1. Check line routing.
1. Line improperly routed
in head.
2. Rewind line tightly and evenly.
2. Line improperly
wound onto spool.
3. Incorrect line size
4. Not enough line
outside of head.
3. Use only .065 in. (1.65mm) dia. line.
4. Remove cover and pull 4 in.
(10 cm) of line out of head.
5. Clean unit.
5. Dirt buildup on unit.
Line welds onto 1. Line size is incorrect.
1. Use only .065 in. (1.65mm) dia. line.
2. Replace with correct spool.
3. Cut with tip of line fully extended.
2. Incorrect spool.
3. Line is being crowded
against material being
cut.
spool.
Line releases
continuously.
1. Line improperly
routed in head.
2. Spool damaged.
1. Check line routing.
2. Replace spool.
Line usage is
excessive.
1. Line improperly routed
in head.
1. Check line routing.
2. Line size is incorrect.
3. Crowding line against
material being cut.
2. Replace spool.
3. Cut with tip of line fully extended.
4. Spool worn or damaged. 4. Replace spool.
Line pulls back
into head.
1. Too little line outside
of head.
2. Line size incorrect.
1. Remove cover and pull 4 in.
(10 cm) of line outside of head.
2. Use only .065 in. (1.65 mm) dia. line.
7
the warranty period. This warranty does
not cover predelivery set--up or normal
adjustments explained in the instruction
manual.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS,
INC., warrants to the original purchaser
that each new Weed Eaterr brand elec-
tric or cordless product is free from de-
fects in material and workmanship and
agrees to repair or replace under this
warranty any defective Weed Eater
brand electric product within two (2)
years from the original date of purchase.
If your Weed Eater brand electric or
cordless product should fail within the
limited warranty period, return it, com-
plete, prepaid, with proof of purchase, to
the dealer from whom it was purchased
for repair or replacement at the option of
ELECTROLUX HOME PRODUCTS,
INC.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically rec-
ommended by ELECTROLUX HOME
PRODUCTS, INC., for this electric prod-
uct. Additionally, this warranty does not
cover parts that will wear and require re-
placement with reasonable use during
The policy of ELECTROLUX HOME
PRODUCTS, INC., is to continuously im-
prove its products. Therefore, ELEC-
TROLUX HOME PRODUCTS, INC., re-
serves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice or obligation to
any purchaser.
8
|