WST6003 Flat Fan Heater
11. To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surfaces, like a bed, where openings may
become blocked. Use the Heater on flat, dry surfaces only.
12. A Heater has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Heater only as directed in this manual, Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
14. Avoid the use of an extension cord because the extension cord may
overheat and cause risk of fire. However, if you must use an extension
cord, the cord shall be #14 AWG minimum size and rated not less than
1875 watts.
15. If the Heater will not operate: See specific instructions on Auto Safety
Shut Off.
16. Do not place the Heater on an uneven or small surface which might
allow it to tip or fall.
17. Do not operate the Heater with Heater Guards removed.
18. The Heater must be 12 inches (300mm) distance away from the wall or
other objects.
19. This Heater includes a visual alarm to warn that parts of the Heater are
getting excessively hot. If the alarm flashes, immediately turn the Heater
OFF and inspect for any objects on or adjacent to the Heater that may
cause high temperatures. DO NOT OPERATE THE HEATER WITH THE RED
SAFETY LIGHT FLASHING .
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
2
ADDITIONAL IMPORTANT SAFEGUARDS
CAUTION HOT SURFACES: This Heater generates heat during use. Proper
precautions must be taken to prevent the risk of burns, fires or other
injury to persons or damage to property.
CAUTION: This Heater is hot during operation and retains heat for some time
after turning OFF. Do not place anything on top of the Heater while it is
operating or while it is hot.
1. A person who has not read and understood all operating and safety
instructions is not qualified to operate this Heater. All users of this
Heater must read and understand this Owner’s Manual before operating
or cleaning this Heater.
2. Unplug Heater from outlet and allow to cool before attempting to
store unit.
3. The cord to this Heater should be plugged into a 120V AC electrical
outlet only.
4. Do not use this Heater in a garage.
5. When using this Heater, provide adequate air space above and on all
sides for air circulation. Do not operate this Heater while it is touching
or near curtains, wall coverings, clothing, dish towels or other
flammable materials.
6. Use this Heater only on a level surface.
7. Do not operate Heater when the Red Safety Light is flashing.
Polarized Plug
This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit into a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not attempt to
modify the plug in any way.
Electric Power
If the electrical circuit is overloaded with other appliances, your appliance
may not operate properly. It should be operated on a separate electrical
circuit from other appliances.
3
Getting To Know Your Westinghouse
WST6003 Flat Fan Heater
Product may vary slightly from illustrations
Air Intake
(not shown)
Thermostat
Dial
Heater/
Fan Dial
Red Safety
Light
Amber Power
ON/OFF Light
Front
Safety Grill
OFF Fan
LO
Top Grill
HI
Heater/Fan
Dial
MIN
Thermostat Dial
MAX
Amber Power
ON/OFF Light
Red Safety
Light
4
BEFORE USING FOR THE FIRST TIME
Your WST6003 Flat Fan Heater is designed for space heating or as a
supplementary heat source. It is not intended to be the main source of heat.
NOTE: Make sure the Heater Dial is in the
OFF position before operating.
1. Place your Heater on a level, stable surface. It is recommended that the
Heater be placed on the floor, where it can keep the lower level of the
room warm. Be sure the sides and back of the Heater are at least 3 feet
away from any combustible materials. DO NOT COVER the Air Intake or
the Front Safety Grill.
2. Plug the Flat Fan Heater into a 120V AC electrical outlet.
3. There are 3 settings on the Heater Dial:
Fan / Breeze Fan only LO Heat / 750 Watts HI Heat /1500 watts
OPERATING INSTRUCTIONS
Setting the Thermostat for Heat
1. When heating a cold area in the room, first turn the Thermostat Dial to
the MAX position.
2. Next, turn the Heater Dial to either LO or HI Heat.
3. The amber Power ON/OFF Light will illuminate when you turn the
Heater Dial from the OFF position. The Fan will begin to rotate.
Your Heater will quietly and efficiently heat your area.
4. When the desired temperature is reached, turn the Thermostat Dial
counter-clockwise to a lower setting until the Fan turns itself OFF.
5. The temperature is now pre-set.
6. When you are finished using the Flat Fan Heater, turn the Heater/Fan
Dial to the OFF position, turn the Thermostat Dial to the minimum
setting, and unplug from the electrical outlet.
NOTE: The Heater will cycle ON and OFF to maintain this temperature.
This is normal.
NOTE: To prevent the Heater from cycling, turn the Thermostat Dial to a
lower setting.
5
WARNING: The red Safety Light will serve as a visual alarm to alert you that
the thermal cut-off is broken. At this time, the Heater will turn itself OFF.
If both the red and the amber Lights are illuminated, immediately turn the
Heater/Fan Dial to the OFF position, turn the Thermostat Dial to MIN and
unplug the cord from the electrical outlet. (See Auto Safety Shut Off
section of this manual for more information.)
Setting the Thermostat for Breeze Fan Only
1. You may use your Heater Fan to create a comfortable breeze by
circulating air only. When using the Fan, first turn the Thermostat Dial
to the MAX position.
2. Next, turn the Heater Dial to Fan.
3. The amber Power ON/OFF Light will illuminate when you turn the
Heater Dial from the OFF position. The Fan will begin to rotate.
Your Heater will quietly and efficiently provide a cool and comfortable
breeze to your area.
4. When the desired temperature is reached, turn the Thermostat Dial
counter-clockwise to a lower setting until the Fan turns itself OFF.
5. The temperature is now pre-set.
6. When you are finished using the Flat Fan Heater, turn the Heater Dial to
the OFF position, turn the Thermostat Dial to the minimum setting,
and unplug from the electrical outlet.
NOTE: The Heater will cycle ON and OFF to maintain this temperature.
This is normal.
NOTE: To prevent the Heater from cycling, turn the Thermostat Dial to a
lower setting.
6
Frost Watch
If your Heater is plugged in and in operation and set at the lowest setting
(the Heater/Fan Dial set to LOW and the Thermostat Dial set to MIN) the
Heater will remain OFF unless the temperature drops below 41ºF. At 41ºF
the Heater will automatically turn ON and will cycle ON and OFF to keep the
area at a constant temperature.
Auto Safety Shut Off
When the temperature rises to an unsafe level, usually due to an obstruction
of the Front Safety Grill or Air Intake, the red Safety Light will illuminate and
the Heater will turn itself OFF. Immediately turn the Heater/Fan Dial to the
OFF position, turn the Thermostat Dial to LOW. Remove the plug from the
outlet and allow the Heater to cool for 30 minutes. If necessary, remove the
object causing the problem; then plug into the outlet and turn the
Heater/Fan Dial. If the Heater’s red Safety Light is still illuminated, call
Consumer Service for authorization for return or repair.
DO NOT USE A MALFUNCTIONING HEATER.
7
USER MAINTENANCE INSTRUCTIONS
This appliance is permanently lubricated and will not require additional
lubrication for the life of the unit. There are no user serviceable parts inside
the unit. Servicing by our Authorized Service Center is required to avoid
damage to internal components.
Cleaning
Always turn the Heater/Fan Dial to the OFF position, turn the Thermostat
Dial to LOW and unplug from the electrical outlet before cleaning your
Heater. Accumulated dust may be removed from the Heater with a soft cloth
or vacuum cleaner using the dusting brush attachment. Interior dust can
often be removed by using a vacuum cleaner in its blower mode with a
crevice attachment.
Your Flat Fan Heater may also be cleaned with a cloth that has been
moistened with a solution of mild detergent and water. Dry the outside of
the unit thoroughly with a soft, dry cloth before operating.
CAUTION: DO NOT immerse Heater in water or allow water to drip into
the Heater housing, as this could create an electric shock hazard.
NEVER use gasoline, benzene, thinner, etc., as these chemicals will
damage the unit.
Storage
1. Allow Heater to cool before storage. Never store the Heater while it is
hot or still plugged in.
2. Gather the cord in loops and secure with a twist tie to store. Never let
the power cord come in contact with sharp edges or get compressed by
heavy objects.
3. Never wrap cord tightly around appliance. Do not put any stress on cord
where it enters the unit, as this could cause cord to fray and break.
4. Store the Heater in its box or in a clean, dry place.
8
LIMITED ONE-YEAR WARRANTY
Warranty Coverage: This product is warranted to be free from defects in materials or
workmanship for a period of one (1) year from the original purchase date. This product warranty is
extended only to the original consumer purchaser of the product and is not transferable. For a period
of one (1) year from the date of original purchase of the product, our Repair Center will, at its
option, either (1) repair the product or (2) replace the product with a reconditioned comparable
model. These remedies are the purchaser's exclusive remedies under this warranty.
Warranty Service: To obtain warranty service, you must call our warranty service number at
1-800-233-9054 for return instructions on how to deliver the product, in either the original
packaging or packaging affording an equal degree of protection to the Repair Center specified
below. You must enclose a copy of your sales receipt or other proof of purchase to demonstrate
eligibility for warranty coverage.
To return the appliance, ship to:
To contact us, please write to, call, or email:
ATTN: Repair Center
708 South Missouri Street
Macon, MO 63552 USA
Consumer Relations Department
PO Box 7366
Columbia MO 65205-7366 USA
1-800-233-9054
What Is Not Covered: This warranty does not cover damage resulting from misuse, accident,
commercial use, improper service or any other damage caused by anything other than defects in
material or workmanship during ordinary consumer use. This warranty is invalid if the serial number
has been altered or removed from the product. This warranty is valid only in the United States and
Canada.
LIMITATION ON DAMAGES: THERE SHALL BE NO LIABILITY FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION
ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS, INCLUDING, WITHOUT
LIMITATION, IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE OR USE ON THIS PRODUCT ARE LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights and you may have other rights
under the laws of your jurisdiction.
WESTINGHOUSE, ꢀ and “You Can Be Sure...If It's Westinghouse” are trademarks
of WESTINGHOUSE ELECTRIC CORPORATION and used under license.
©2005 All rights reserved. Patent Pending
Made in China
P/N 61712
6/05
|