Woodstock TV Antenna d4327 d4328 User Manual

Model D4327/D4328  
Quick Release Wood Vise  
Instruction Sheet  
Introduction  
Your new Model D4327/D4328 Quick Release Wood Vise  
(Figure 1) is designed to fit on workbenches 214" and  
1
thicker, but can be adapted to workbenches down to 1 2  
thick by using a shim. Holes are pre-drilled in the jaw  
faces to attach aftermarket or shop-built wood clamping  
vise jaw pads.  
"
D4327 Specifications  
Jaw Width .................................................7"  
Mounting Height (Workbench Thickness) ..........214  
"
Maximum Jaw Opening ..................................8"  
Weight................................................21 lbs.  
D4328 Specifications  
Figure 1. Quick release wood vise.  
Jaw Width .................................................9"  
Mounting Height (Workbench Thickness) ..........214  
Maximum Jaw Opening ................................ 10"  
Weight................................................25 lbs.  
"
Workbench  
Shim  
Vise  
Installation  
1. Have another person hold the vise up against the  
workbench in the desired mounting location. If the  
workbench has holes for bench dogs, make sure the  
bench dog on the vise is aligned with those holes.  
Figure 2. Shim placed between workbench  
and vise for workbenches under 214".  
Note: If the workbench is less than 214" thick, use a  
piece of scrap wood (Figure 2) between the vise and  
workbench as a shim. Cut the shim to the necessary  
thickness so the vise does not protrude above the  
workbench after mounting.  
Mounting Holes  
for Wood  
Screws  
2. Pencil mark the workbench through the mounting  
Mounting  
Holes for Lag  
Screws  
holes to establish locations to drill pilot holes.  
3. Use a 18" drill bit to drill pilot holes approximately  
112" deep in the face of the workbench, where the  
wood screws will be used (see Figure 3).  
Figure 3. Mounting hole locations.  
COPYRIGHT © MARCH, 2012 BY WOODSTOCK INTERNATIONAL, INC.  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT  
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.  
#14922ST  
Printed in China  
 
D4327/D4328 - For Models Manufactured Since 3/12  
D4327 Parts  
4
3
14  
13  
5
16  
18  
6
9
17  
8
7
10  
11  
15  
21  
22  
20  
2
1
12  
19  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
PHLP HD SCR M5-.8 X 12  
1
2
XD4327001 FLAT COIL SPRING 4 X 3  
XD4327002 SLOTTED NUT M12-1.75  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
XPS08M  
XD4327013 FINGER BOLT M8-1.25 X 20  
XD4327014 LOCK DOG 50 X 25 X 10  
XD4327015 QUICK RELEASE LEVER  
3
4
5
XD4327003 FIXED HOUSING 180 X 160 X 30  
XD4327004 SLIDING HOUSING 110 X 110 X 180  
XD4327005 GUIDE ROD 22 X 320  
XPW06M  
FLAT WASHER 12MM  
6
7
8
9
10  
11  
XD4327006 LEADSCREW 33 X 400  
XD4327007 TORSION BAR 26 X 285 X 2  
XD4327008 GUIDE ROD SUPPORT  
XD4327009 HANDLE BAR W/KNOB  
XD4327010 REMOVABLE HANDLE KNOB  
XD4327011 RETAINER FORK  
XD4327017 COTTER PIN 3 X 40  
XD4327018 WAVY WASHER 12MM  
XPB04M  
HEX BOLT M6-1 X 10  
LOCK WASHER 6MM  
XPLW03M  
XD4327021 QUICK RELEASE HALF NUT  
XD4327022 HALF NUT HOUSING BRACKET  
Parts breakdown provided for reference only. Not all parts shown are available for purchase.  
-3-  
 
D4327/D4328 - For Models Manufactured Since 3/12  
D4328 Parts  
4
3
14  
13  
5
16  
18  
6
9
17  
8
7
10  
11  
15  
21  
22  
20  
2
1
12  
19  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
PHLP HD SCR M5-.8 X 12  
1
2
XD4327001 FLAT COIL SPRING 4 X 3  
XD4327002 SLOTTED NUT M12-1.75  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
XPS08M  
XD4327013 FINGER BOLT M8-1.25 X 20  
XD4327014 LOCK DOG 50 X 25 X 10  
XD4327015 QUICK RELEASE LEVER  
3
XD4328003 FIXED HOUSING 230 X 160 X 30  
4
5
6
7
8
9
10  
11  
XD4328004 SLIDING HOUSING 230 X 110 X 110  
XD4328005 GUIDE ROD 22 X 380  
XD4328006 LEADSCREW 33 X 460  
XD4328007 TORSION BAR 26 X 335 X 2  
XD4328008 GUIDE ROD SUPPORT  
XD4328009 HANDLE BAR W/KNOB  
XD4327010 REMOVABLE HANDLE KNOB  
XD4327011 RETAINER FORK  
XPW06M  
FLAT WASHER 12MM  
XD4327017 COTTER PIN 3 X 40  
XD4327018 WAVY WASHER 12MM  
XPB04M  
HEX BOLT M6-1 X 10  
LOCK WASHER 6MM  
XPLW03M  
XD4327021 QUICK RELEASE HALF NUT  
XD4327022 HALF NUT HOUSING BRACKET  
Parts breakdown provided for reference only. Not all parts shown are available for purchase.  
-4-  
 

Weslo Bicycle WLEL19020 User Manual
Weslo Exercise Bike WLEL718070 User Manual
Whirlpool Oven gas range User Manual
Woodstock Drill M1039 User Manual
Xantrex Technology Power Supply 42V 10A User Manual
Xpelair Fan PX12 User Manual
Zanussi Cooktop 200476 User Manual
Zanussi Freezer DV17 User Manual
Zanussi Refrigerator ZUD 9124 A User Manual
Zebra Technologies Printer SL5000r T5000r User Manual