REFRIGERATOR-
FREEZER
ZA 98/3 W
INSTRUCTION BOOKLET
2222 183-71
CONTENTS
Instructions for the User
Instructions for the
Installer
2
4
5
Important Safety Information
16
17
Technical Specification
Description of the Appliance
Installation
Positioning
Operation
17
17
Before using
5
5
5
5
6
6
7
7
7
6
8
8
8
9
9
Rear Spacers
Control panel
Start your appliance
Temperature control
Freezing fresh food
Frozen food storage
Thawing
18
19
Electrical Connection
Door Reversal
Making ice cubes
Cold accumulators
Fresh food refrigeration
Movable shelves
Positioning the door shelves
Drawer
Cool Check Guide
Freezing calendar
10
11
Hints and Tips
Maintenance and Cleaning
Internal cleaning
11
11
11
11
12
External cleaning
When the appliance is not in use
Changing the light bulb
Defrosting
13
14
14
15
Something Not Working
Service and Spare Parts
Customer Care
Guarantee Conditions
2222 183-71
3
DESCRIPTION OF THE APPLIANCE
A
B
C
D
L
E
K
J
I
F
H
G
A- Control panel
B- Interior light
C- Dairy compartment
D- Movable shelf
E- Can storage shelf
F- Bottle storage shelf
G- Compartments for frozen food storage
H- Compartment for freezing fresh food and frozen food storage
I - Drawer
J - Glass shelf
K- Cool Check Temperature Guide
L - Storage shelves
4
OPERATION
Before using
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Control panel
A B C D
E
F
G
A -
B -
C -
D -
E -
Alarm light - Red
F -
Fridge Pilot light - Green
Fast freeze light - Amber
Fast freeze switch
G -
Fridge Thermostat control knob
Pilot light - Green
Freezer Thermostat control knob
Control Panel
Start your appliance
A. Alarm light
Allow the appliance to stand for 2 hours after
installation.
If the alarm light (A) illuminates, it indicates that the
temperature within the freezer has reached a level
where safe food storage is no longer ensured.
Insert the plug into the wall socket. The pilot light (D)
will illuminate to show that the appliance is on.
Turn the thermostat control (G) to a midway setting.
The pilot light (F) will illuminate. Leave the appliance
for approximately 4 hours for the correct temperature
to be reached before placing food inside.
When the freezer is first switched on, the alarm light
will stay on until the temperature has dropped to a
safe level for the storage of frozen food.
B. Fast freeze light
To switch off the appliance turn the thermostat
control to position “O” .
The fast freeze light is illuminated, to show that the
fast freeze function is working.
Temperature control
C. Fast freeze control switch
When you place fresh food in the appliance, press
the fast freeze control switch.
The temperature within the freezer is controlled by
the thermostat situated at the top of the cabinet.
To operate the freezer proceed as follows:
D. Pilot light
Turn the thermostat control knob beyond the «O»
position.
The operation light is illuminated continuously, to
show that the appliance is on.
When you first start the freezer, we suggest that you
turn the thermostat control to a medium setting. For
easier turning of this control, use a small coin.The
internal temperature of the freezer is automatically
adjusted by the thermostat to ensure safe food
storage.
E.Thermostat control knob
Turn the thermostat control knob clockwise to
required setting.
However, if the appliance is working in unfavourable
room conditions such as
-
-
poor ventilation,
high temperature,
5
-
frequent door openings,
Frozen food storage
it may be necessary to select a more suitable
setting.
When you first start the freezer or if the freezer has
been out of use for some time, we advise you to run
your appliance for at least 12 hours in the «fast
freeze» mode before storing frozen food.
To obtain a colder temperature, turn the thermostat
control to the larger G; to obtain a warmer
temperature turn the control to the smaller
G.
To obtain the best performance from this appliance,
you should:
If large quantities of food are to be stored, remove all
drawers and baskets from appliance and place food
on the cooling shelves.
Pay careful attention not to exceed load limit stated
on the side of the upper section (where
applicable).
Freezing fresh food
In any 24 hour period you can freeze up to 13 kg of
fresh food.
When you first start the freezer or after a period of
non-use, press the fast freeze switch 12 hours
before you want to freeze your food (the yellow light
(B) illuminates).
Do not exceed the storage period indicated by the
manufacturer.
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
If the freezer is already in operation, the fast-freeze
knob should be activated about 2-3 hours before
freezing fresh food.
Important
This time can be shortened, depending on the
quantity of food to be frozen. After the time has
elapsed place the food to be frozen in the upper
compartment of the freezer as these are the coldest
parts.
Do not put carbonated liquids, (fizzy drinks etc.), in
the freezer compartment.
Ice Iollies, if consumed immediately after removal
from the freezer, can possibly result in a low
temperature skin burn.
In order to freeze the quantity indicated on the rating
plate, arrange the food directly in contact with the
cooling surfaces. If the food is frozen in the baskets,
the maximum quantity that can be frozen is slightly
less.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
“frost/freezer burns”.
Once the food is completely frozen (which could take
up to 24 hours) press again the fast freeze switch;
the yellow light (B) goes off.
Important
In the event of a power cut do not open the door. The
food in the freezer will not be affected if the power
cut is short and if the freezer is full. Should the food
begin to thaw, it must be consumed quickly and must
not be re-frozen.
Distribute the frozen food packages in the other
compartments, so that the top compartments can be
used for a further freezing operation.
-
-
-
The food to be frozen must be fresh and of the
best quality.
Do not allow fresh food to touch food which is
already frozen.
During the freezing process, ensure that the
freezer door remains closed.
6
Thawing
Fresh food refrigeration
Frozen food, prior to being used, can be thawed in
the fridge or at room temperature depending on the
time available. Small food items may even be cooked
from frozen; in this case cooking will take longer.
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Any frozen food which is allowed to thaw accidentally
should either be eaten as soon as possible or thrown
away. Alternatively, if the food is uncooked and has
not been completely defrosted it can be cooked and
then refrozen.
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Meat, fish and fruit should be thawed in the
refrigerator compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Raw meat (beef, pork, lamb & Poultry): wrap in
polythene bags and place on the glass shelf on the
top of the salad crispers.
Meat can only be stored safely in this way for
one or two days at the most.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the salad crispers.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
oven instructions, particularly regarding the
placement of aluminium wrapping or containers in
the oven.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
Defrosted cooked food must never be refrozen.
Making ice cubes
The appliance is provided with one or more trays for
ice-cubes trays.
Fill the tray(s) 3/4 full to give the ice space to expand
and place them in the freezer compartment.
To release the ice cubes simply give the tray a slight
twist.
Do not use sharp or metallic instruments to remove
the trays from the freezer.
Cold accumulators
The freezer contains two cold accumulators. Place
the cold accumulators in the FAST FREEZE
compartment. The cold accumulators increase
storage times in the event of a power cut or
breakdown.
Removal of these units wll increase the capacity of
the fast freezing compartment but will reduce
storage times in the event of a power cut or
breakdown.
7
Movable shelves
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
D338
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To do this proceed as shown in the diagram.
PR261
Drawer
The drawer is suitable for storing fruit and
vegetables.
There is a separator inside the drawer that can be
placed in different positions to allow for the
subdivision best suited to personal needs.
8
Cool Check Guide
The guide consists of a temperature sensitive strip
sealed in a shelf trim.
When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.
TOO WARM
Positioning of the Cool Check
The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.
If the Cool Check showsTOOWARM
In certain conditions the temperature guide may
show TOO WARM if:
•
•
•
The fridge is switched off
ZANUSSI
The door has been recently opened
A quantity of warmer food has been introduced to
the fridge
CCOO2
•
The fridge temperature is above the
recommended maximum for the safe storage of
food.
The cool check will change to show “TOO WARM“
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.
Hints and Tips
•
•
•
The guide is only suitable for use in the model
supplied.
The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the thermostat to a colder
setting leave overnight and examine again the
following morning.
The guide will not operate in the freezer
compartment.
When cleaning the shelf take care not to immerse
in water, and wipe away any spills.
Freezing Calendar
The symbols show different types of frozen goods.
The numbers indicate storage times in months for the appropriate types of frozen goods.
9
HINTS AND TIPS
Energy Saving Advice
Normal Operating Sounds
•
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, and to the cooling
plate/evaporator.
•
•
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
•
•
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
•
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages
before placing them in the freezer.
A thermostat controls the compressor, and you
will hear a faint ’click’ when the thermostat cuts in
and out.
•
•
Always leave warm food to cool down to room
temperature before placing in the fridge.
Food Storage
Food which is to be frozen (when cool) should be
placed in the fridge before being transferred to
the freezer.
To obtain the best performance from your fridge-
freezer
•
•
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of
the refrigeration unit.
•
•
Do not store warm food or evaporating liquids.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container is
advisable. When you arrive home place the frozen
food in the freezer immediately.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
•
•
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
•
Ensure there are no obstructions preventing the
door from closing properly.
Do not push food together too much, try to allow
air to circulate around each item.
In the Event of a Power Failure
•
•
Do not store food uncovered.
If there is a power failure during the storage of frozen
foods, keep the door closed. If the temperature within
your freezer should rise, do not refreeze the food
without checking its condition. The following
guidelines should assist you:
Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
•
•
•
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
Ice-cream: Once thawed should be discarded.
Lean food keeps better and longer than fatty food,
salt reduces the storage time.
Fruits & Vegetables: If soft should be cooked and
used up.
Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airtight seal .
Breads & Cakes: Can be refrozen without danger.
Shellfish: Should be refrigerated and used up
quickly.
•
Packaging which is swollen or has traces of
refrozen water droplets on the pack could indicate
that the product has not been kept at a suitable
temperature and that it may have lost its original
quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage times indicated by the
manufacturer.
Cooked Dishes: i. e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: Can be refrozen providing
there are still ice crystals remaining within them.
Small Joints: Should be cooked and can then be
refrozen as cooked dishes.
Chicken: Should also be cooked and refrozen as a
fresh dish.
10
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Changing the light bulb
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED
CLEANING PRODUCTS OR WAX
POLISHES,TO CLEAN THE INTERIOR AS
THESE WILL DAMAGE THE SURFACE AND
LEAVE A STRONG ODOUR.
Unscrew the light cover and then pull it outward
toward the middle of the cabinet. Unscrew the bulb
and replace it with a new 25 watt bulb (available from
your nearest Service Force Centre).
External cleaning
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
Replace the light cover by sliding it into its original
position and replacing the screw.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
You MUST ensure that the appliance is switched
OFF.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
PR259
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
11
Defrosting
Refrigerator
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via a
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
D037
Freezer
When the frost has reached a thickness of up to
4mm it can be removed using the ice scraper
provided with the appliance. During this operation it
is not necessary to disconnect the appliance from
the mains and remove the food. Never use metal
tools for this operation.
For complete defrosting (once or twice a year)
proceed as follows:
-
turn the thermostat dial to the «OFF» position (O)
or disconnect the appliance from the mains.
-
Remove any food from inside the freezer and
fridge, wrap it in several sheets of newspaper and
store in a cool,dry place.
-
Leave the door open and insert the ice scraper
under the channel in the centre of the lower part
of the appliance; place a low-sided container
beneath the scraper to collect the water (see fig.).
-
-
-
Clean and dry thoroughly.
Replace the scraper in one of the drawers .
Reconnect the appliance to the mains or reset
the thermostat to the normal position.
-
After letting the appliance run for at least half an
hour, replace the previously removed food into
the compartment.
D068
Important
When defrosting the freezer, the fridge is also
controlled by the thermostat and will not be
operational during this period. A temperature rise of
the frozen food packs, during defrosting, may
shorten their safe storage life.
12
SOMETHING NOT WORKING
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made, even if the appliance is under guarantee.
Before contacting your local Service Force Centre, check the following points:
Symptom
Solution
No power to the appliance
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come on
Ensure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
The temperature in the fridge or freezer section is
too high
Check the thermostat control knob is turned to the
correct setting relative to ambient conditions.
Check the ambient temperature is within the
appliance’s operating limits, please refer to the
installation section in this instruction book.
Relocate the appliance if necessary.
The freezer door will not open
Has door just been opened? If so leave for a few
minutes to allow the air pressure to equalise.
The compressor runs continously
Adjust the thermostat control knob to give correct
temperature control. See “Setting the temperature”.
Check that the doors are closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Check that air ventilation is not obstructed.
Excessive frost and ice has built up
Ensure the doors are not left open.
Check that nothing is preventing the doors from
closing.
Is the door gasket intact and clean.
Has advised periodic defrosting been carried out.
Noise
Refer to normal operating sounds.
Water under the salad crispers
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
13
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Zanussi Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products,
please contact our Customer Care Department by letter or telephone at the address below or visit our website
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727 (*)
* calls to this number may be recorded for training purposes.
14
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of
use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 29
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)1753 219 897
Nürnberg
Pordenone
Stockholm
Slough
Sweden
UK
15
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
185
cm
Width
Depth
60
cm
cm
62,5
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
180 W
AVERAGE DAILY UNITS ELECTRICITY *
GROSS CAPACITY
0.64 kWh
Fridge
222 l
86 l
Freezer
NET CAPACITY
Fridge
221 l
82 l
Freezer
STAR RATING
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
16
INSTALLATION
Important
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on “Door reversal”.
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located at the left on the inside of the
appliance.
The following table shows which ambient temperature
is correct for each climate classification:
SN +10°C to + 32°C
A
B
N
+16°C to + 32°C
ST +18°C to + 38°C
+18°C to + 43°C
T
NP00
It should be located in a dry atmosphere, out of direct
sunlight and away from extreme temperature e.g. not
next to a boiler or radiator, or in a very cold room e.g.
an outhouse, where the temperatures may fall below
10°C (50°F). If these temperatures are exceeded i.e.
colder or warmer, then the appliance may not operate
correctly.
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There must
also be at least 100 mm (4”) distance between the top
of the cabinet and any overhanging kitchen furniture
(A). Ideally, the appliance should not be positioned
beneath overhanging furniture (B).
There should also be a gap of 25 mm either side of the
appliance. Do not obstruct the space underneath. The
back of the cabinet may be placed close to the wall but
must not touch it. DO NOT install in places with
restricted ventilation.
D200
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then re-tighten the screws.
D594
17
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
WARNING:THIS APPLIANCE MUST BE
EARTHED.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green andYellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
BROWN
BLUE
CORD CLAMP
D207
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
18
Door reversal directions
1. Disconnect from the electricity supply.
E
E
2. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
F
F
3. Remove the ventilation grill (D).
4. remove the bottom hinge (E) by unscrewing its
three fixing screws;
D
F
5. Remove the freezer door by releasing it from the
middle hinge (H).
PR18
6. Unscrew the middle hinge.
7. Remove the fridge door by releasing it from the
top hinge pin (G).
H
8. Remove the pin then mount these on the side,
after having removed the small plugs which
should then be fitted on the opposite side.
9. using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge;
10.Refit the fridge door and replace the middle hinge
to the left hand side.
11.reassemble the lower hinge (E) on the opposite
side, using the screws previously removed. Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;
12.reassemble the door;
G
13.refit the ventilation grille (D), clipping it into place;
The doors can be aligned by adjusting the middle
hinge.
The middle hinge can be adjusted horizontally, after
having slackened the two screws with a screwdriver.
Important
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
Printed on recycled paper
19
© Electrolux plc 2003
|